Home / Journal / Yarn count and consumption

Yarn Count and Consumption in Crochet Costing

Updated 18 November 2026 · Yarn count, linear density, consumption and costing

Two quotes for the same crochet toy, twelve per cent apart, and both factories are telling the truth. One costed 22 grams of yarn per piece because that is what the sample weighed. The other costed 25 grams because that is what the yarn label promised. The gap is not dishonesty; it is the difference between a count that was measured and a count that was assumed.

Yarn count is the least glamorous number in a crochet programme and the one that moves money most reliably. It decides how many metres arrive in a kilogram, how many pieces a kilogram makes, what a piece weighs, what the freight costs, and whether the tenth container matches the first. It is also the number most often copied from a supplier's label without anyone checking whether the label and the laboratory mean the same thing by it.

This article is about the three decisions behind that twelve per cent: what a count number actually states, how the three systems in common use convert into each other without rounding errors, and how consumption per piece is measured rather than estimated. It sits alongside the costing structure itself, which is covered separately in costing after the quotation; here the subject is only the yarn line.

In this article

1. What a count number states · 2. The conversions you actually need · 3. Why the label and the lab disagree · 4. From metres to grams · 5. Calibrating the stitch-count route · 6. Where the error actually comes from · 7. What to write in the RFQ · 8. Craft weights are not measurements · 9. A worked quote · 10. What we do before quoting · 11. Questions

1. What a count number states

A yarn count states one physical quantity: mass per unit length, or its reciprocal, length per unit mass. Everything else — the three systems, the four notations, the arguments about 4-ply — is a convention for expressing that single quantity. The confusion is not in the physics; it is in the direction of the fraction.

There are two families. Direct systems state mass per fixed length: a heavier yarn gets a bigger number. Tex is the direct system, defined as grams per 1,000 metres, and it is the one the international standard designates. Indirect systems state length per fixed mass: a finer yarn gets a bigger number, which is why a 2/60 yarn is much finer than a 2/20 and why "higher count" means opposite things in the two families. Nm, the metric count, is metres per gram. Ne, the cotton count, is the number of 840-yard hanks in one pound. Denier, still universal in filament and in some craft yarns, is grams per 9,000 metres.

The unit system itself is standardised. ISO 1144:2016, the second edition published on 15 September 2016 and last reviewed and confirmed in 2021, sets out the principles and recommended units of the Tex system for designating the linear density of fibres, yarns and similar products. What it deliberately does not do is prescribe a test method — it fixes the unit and the reporting format, and leaves measurement to ISO 2060:1994 for yarn from packages by the skein method, or to ASTM D1907/D1907M for skein-based determination, or to ASTM D1059 for short lengths ravelled out of a fabric.

That division matters commercially. If a purchase order specifies "30 tex" it has specified a unit, not a measurement. If it specifies "30 tex, determined by ISO 2060 on conditioned yarn" it has specified both, and the difference between those two sentences is the difference between a number that can be argued about and a number that can be checked.

2. The conversions you actually need

Five relationships cover every conversion a crochet programme needs, and none of them requires a lookup table once the definitions are understood.

SystemStatesRelationship to tex
texgrams per 1,000 mthe base unit
dtexgrams per 10,000 mdtex = 10 × tex
deniergrams per 9,000 mdenier = 9 × tex
Nm (metric count)metres per gramNm = 1,000 / tex
Ne (cotton count)840-yard hanks per poundNe = 590.5 / tex
NeK (worsted count)560-yard hanks per poundNeK = 885.8 / tex

The two indirect constants are not arbitrary; they fall out of the definitions and the exact unit conversions. One pound is 453.59237 grams and one yard is 0.9144 metres. A yarn of 1 tex is one gram per metre, so one pound of it is 453.59237 metres, which is 496,055 yards, which is 590.5 hanks of 840 yards. Hence Ne = 590.5 / tex. Substituting 560-yard hanks gives 885.8 / tex for the worsted count. Anyone who works in both systems regularly should be able to reproduce those two numbers rather than look them up, because a transposed constant is a silent twelve per cent error in a quote.

Three examples, all exact arithmetic rather than tables:

SpecificationtexNmNeDenier
Fine crochet cotton, 2/60 Nm33.33019.7300
Soft-toy yarn, 2/30 Nm66.7159.9600
Chunky blanket yarn, 300 tex3003.32.02,700

Two things are worth noticing in that table. First, the doubled specification "2/60 Nm" means two plies of a 60 Nm single, and the resultant count is 30 Nm, not 60 — the plies are in parallel, so the length per gram halves. Writing "60/2" instead invites the opposite reading, in which 60 is the ply count and 2 is the count, and no amount of context makes that unambiguous. The convention that has survived in the trade is count first, ply second, but it survives only because most people happen to use it that way; the safe practice is to write the folded construction and the resultant tex explicitly.

Second, the differences between these three yarns are not linear in feel. Going from 33 tex to 300 tex is a ninefold increase in mass per metre, and a hook size, a stitch height and a piece weight all change with it. A cost sheet built on the assumption that "chunky is about three times the sport weight" will be wrong by a factor of three.

3. Why the label and the lab disagree

Put a cone on a balance, reel 100 metres, weigh it, and compare with the label. The number that comes back will usually be within a few per cent, and occasionally it will be off by more than that — not because anyone lied, but because three separate things are being measured.

The first is moisture. Yarn is a hygroscopic material, and its mass depends on the water in it at the moment of weighing. Trade therefore uses a conventional figure rather than the actual one: the commercial or conventional moisture regain, tabulated per fibre type, which for cotton is 8.5 per cent and for wool 16 per cent. Commercial mass is the oven-dry mass grossed up by that conventional figure, an agreed fiction that makes a kilogram in July comparable with a kilogram in January. ASTM D1909 is the table of commercial moisture regains; ISO 6741-1:1989 sets out how the commercial mass of a consignment is determined and calculated.

The commercial consequence is direct. One kilogram of cotton yarn at 8.5 per cent regain contains 921.7 grams of dry fibre and 78.3 grams of water, and the buyer pays for both. That is not a defect in the system — it is the system, and every party to a yarn contract is buying on the same basis. What goes wrong is when one party quotes on commercial mass and the other costs on oven-dry mass, or when a specification states a count without stating which basis it is expressed on.

The second is the method. ASTM D1907/D1907M-12(2025) is the skein method for yarn in package form, and it carries seven options depending on whether the yarn is scoured before weighing, weighed conditioned or oven-dried, and whether the result is adjusted for commercial regain or for a commercial allowance that also covers finish. Option 1 — unscoured, conditioned yarn — is the one generally used for yarns spun on the cotton system; Options 6 and 7, scoured and oven-dried plus regain or allowance, are generally used for filament yarns and for wool-containing yarns. Two laboratories can both be conforming and still report different numbers because they selected different options, which is why the option belongs in the specification and not in the laboratory's discretion.

The third is the length. ASTM D1907 is applicable to yarns finer than 2,000 tex, and to yarns that stretch less than 5 per cent when tension rises from 0.25 to 0.75 cN/tex — a range that covers most crochet yarns comfortably and excludes some elasticated ones. ASTM D1059 measures short lengths ravelled out of a fabric, which is faster and uses less material but has higher variance because it does not average over many metres. A short-length result on a single 10 cm specimen is a production check, not a certificate.

What variesTypical effect on the stated countHow to close it
Moisture basisDepends on fibre; cotton moves about 8.5 per cent between oven-dry and commercialState the basis, and quote on commercial mass
Test option selectedA few per cent between conditioned and oven-dry-plus-regainName the standard and the option
Specimen lengthWider scatter on short lengthsUse the skein method for acceptance, short lengths for checks
Nominal versus actual countManufacturing tolerance, stated by the spinnerAgree a tolerance and test against it

4. From metres to grams

Consumption is where the count becomes money. The bridge is one line of arithmetic: mass in grams equals length in metres multiplied by tex, divided by 1,000. A piece that consumes 733 metres of 30 tex yarn weighs 22 grams. A kilogram of that yarn contains 33.3 kilometres of it, which is why yarn count and piece weight are the same conversation seen from two ends.

There are three workable ways to establish consumption per piece, and they are not equally good.

Unravel and weigh. Take finished, fully trimmed pieces — not a first-off, not a sample made by the pattern technician — and unravel them. Weigh the yarn. Do it on ten pieces and take the median rather than the mean, because the mean is dragged by the one piece that was reworked. This is the reference method: it measures the object that will be shipped, including the tails, the knots and the joins that a theoretical calculation leaves out.

Area density. Cut a known area from a flat panel, weigh it, and multiply by the panel area. This works for scarves, blankets and bag bodies. It fails on openwork and on shaped pieces, because crochet is a loop structure with holes in it and the mass per square metre of a motif panel depends more on the pattern than on the yarn. Use it as a cross-check, never as the primary number.

Stitch count multiplied by yarn per stitch. Count the stitches, multiply by the average length consumed per stitch, and convert through tex. This is the only route that scales to a new design without making it first, and it is also the route most often used with a borrowed constant that does not apply. If a single crochet in a given yarn and hook consumes 2.5 centimetres, then 1,000 stitches consume 25 metres, which at 30 tex is 0.75 grams. Change the hook one size and that constant moves; change from single to half-treble and it roughly doubles.

5. Calibrating the stitch-count route

The stitch-count route is legitimate, but only after it has been calibrated against a physical piece. The calibration is short: work ten stitches of each stitch type used in the pattern, in the actual yarn and on the actual hook, unravel them, measure the length, divide by ten. That gives a length per stitch for each type. Multiply by the stitch count of each row type in the pattern, sum, and convert through tex.

Then check the total against one real piece. If the calculated weight and the weighed weight differ by more than about five per cent, the calibration constant is wrong or the pattern has stitches the count missed — a border worked in a different stitch, a colour change with a long carried thread, a lining, a stuffing opening. The correction factor that reconciles the two is the number worth keeping, per pattern, not per product family.

Two practical notes. Carry the calibration constant in centimetres and the count in tex, and convert once at the end; converting at every step is where unit errors enter. And record which hook the calibration was made on. A pattern that moves from a 2.5 mm to a 3.0 mm hook consumes materially more yarn per stitch at the same stitch count, and the piece grows as well, so both the length per stitch and the stitch count change in the same direction.

6. Where the error actually comes from

Quotes for the same crochet piece rarely differ because one factory is cheaper. They differ because the yarn line was built from different assumptions, and the assumptions fail in three predictable places.

SourceWhat it does to the quoteWhere it surfaces
Count deviation from nominalMoves consumption almost one for one: a yarn 1.7 per cent heavier than nominal consumes 1.7 per cent more mass per metre of the same stitchAt the first bulk delivery, as a shortfall against the yarn purchase
Sample versus bulk weightHand-made samples are tighter and more uniform than production pieces; the difference is usually a few per cent and always in one directionAt the first production run, as a piece that weighs more than the sample
Waste and reworkAdds a percentage that has to be bought, stored and paid for before anything shipsAt reconciliation, when the yarn issued exceeds the yarn in the cartons

The first is the one buyers miss, because it looks like a supplier problem rather than a specification problem. If a yarn is delivered at 30.5 tex against a 30 tex nominal — a 1.7 per cent deviation, well inside normal spinning tolerance — then every metre of it is 1.7 per cent heavier, and a piece built to a fixed stitch count will consume 1.7 per cent more mass. The piece gets slightly bigger and slightly heavier, the yarn runs out earlier, and nobody has done anything wrong. The remedy is a stated tolerance on the count plus a documented count check at goods-in, not a complaint at the end of the run.

The third is where a costing model earns its keep. Waste in crochet is not a single number: it is the tails trimmed at finishing, the yarn carried across colour changes, the pieces rejected at inspection, the rework, and the sampling pulled out of production. Some of it is recoverable as seconds, most of it is not. A programme that buys 220 kilograms of yarn for a job that contains 214 kilograms of product is carrying a 2.8 per cent allowance, and whether that is generous or tight depends entirely on the reject rate that the pattern and the inspection standard actually produce — which is measurable, and worth measuring before the second order rather than after it.

There is a fourth source, less common but more expensive: mixing count bases. A quote built on Nm and a purchase order written in Ne for the same yarn is out by a factor of 1.69, because 590.5 divided by 1,000 is 0.59 and the reciprocal of that is 1.69. That error does not look like a rounding problem on a cost sheet; it looks like a supplier who cannot add up.

7. What to write in the RFQ

Six clauses close the yarn line, and all six are cheap to write.

ClauseWhat it should say
Linear densityResultant tex, plus the single count and ply count where the yarn is folded, so that 2/30 Nm is written as two plies of 30 Nm giving 15 Nm / 66.7 tex
Count toleranceThe permitted deviation on the delivered count, and the method used to check it
Mass basisCommercial mass at the conventional regain for the fibre, with the regain figure stated
Test methodThe standard and the option — for example ASTM D1907 Option 1, or ISO 2060 on conditioned yarn
Consumption basisGrams per piece, measured on finished trimmed pieces, with the number of pieces in the sample and the statistic used
Waste allowanceThe percentage added to net consumption, what it covers, and who owns the balance at reconciliation

The clause that gets skipped most often is the last one. Waste allowances are usually agreed as a number in a quotation and never revisited, which means a programme that improves its reject rate keeps paying the original allowance and a programme that degrades silently absorbs the difference. Writing down what the allowance covers — trims, colour-change carry, rejects, sampling — turns it into something that can be reconciled instead of defended.

Consumption basis is the second most skipped, and the most consequential. "22 grams" means nothing without knowing whether it was weighed on a first-off, on a production piece before trimming, or calculated from a borrowed stitch constant. A sentence stating that it was measured on ten finished trimmed pieces and expressed as a median is worth more than a decimal place.

8. Craft weights are not measurements

Fingering, sport, DK, worsted, aran, chunky. These names are how the craft trade actually talks about yarn, and they are useful for choosing a hook. They are not linear densities. The Craft Yarn Council's standard yarn weight system groups craft yarns into numbered categories and defines each by a gauge range — stitches per four inches in a stated stitch — rather than by mass per unit length. A gauge range is a statement about the fabric; it can be produced by more than one linear density depending on fibre, twist and how tightly the maker works.

The transatlantic problem makes this worse. A UK four-ply and a US four-ply are not the same yarn, and neither name survives translation into tex without a measurement. Within one market the names are stable enough to order against; across markets they are labels that happen to coincide.

For a B2B programme the practical rule is simple: use the craft name to start the conversation and the tex to run it. A specification that says "DK, approximately 125 metres per 50 gram ball" has already given a linear density — 400 tex — without saying so, and it is the metres-and-grams part that the factory can buy against. A specification that says only "DK" leaves the spinner to choose, and the spinner will choose within a range that is wide enough to change the piece weight.

9. A worked quote

Ten thousand crochet toys, 22 grams of yarn each, 30 tex yarn at 12 US dollars per kilogram, three per cent waste allowance. The arithmetic, in the order a cost sheet should do it:

Net yarn is 10,000 pieces at 22 grams, which is 220 kilograms. Adding three per cent gives 226.6 kilograms to purchase. At 12 dollars per kilogram the yarn line is 2,719 dollars, or 27.2 cents per piece. In length terms, 220 kilograms of 30 tex yarn is 7,333 kilometres — a number worth pausing on, because it is the reason a count error compounds: one per cent of 7,333 kilometres is 73 kilometres of yarn that has to be found or paid for.

Now move the assumptions one at a time. A five per cent error in consumption adds 11 kilograms and 136 dollars to the order, which is 1.4 cents per piece. A 1.7 per cent count deviation adds 46 dollars. A waste allowance that should have been six per cent instead of three adds 72 dollars. None of these is dramatic per piece, and all of them are permanent, because the same error is repeated on every order at the same volume. Over a year of monthly shipments the difference between a measured and an assumed yarn line is a five-figure number in dollars and a supplier relationship conducted entirely through shortfall claims.

This is also why the yarn line belongs in the same conversation as the shortfall and overrun tolerance. If the allowance, the delivery tolerance and the count tolerance are agreed together, a shortfall is a reconciliation; if they are agreed separately, a shortfall is a dispute. The mechanics of that reconciliation are set out in shortage and overrun tolerance, and the batch side of the same problem — what happens when the yarn for the re-order is a different dye lot — is in yarn dye lots.

10. What we do before quoting

Our sequence for a new crochet programme: the yarn is specified in tex with its folded construction written out, not as a craft weight; the count of the delivered yarn is checked at goods-in against the stated tolerance, on commercial mass at the conventional regain; consumption per piece is measured by unravelling ten finished trimmed pieces and taking the median, and the stitch-count calculation is kept as a cross-check rather than the primary number; the waste allowance is stated as a percentage with the categories it covers; and the yarn line in the quotation shows grams per piece and kilograms to purchase separately, so that a change in either can be priced without rebuilding the quote.

None of that is exotic. It is the difference between a quote that can be reconciled and a quote that has to be renegotiated — and it costs a sentence in the RFQ rather than a shipment. If you are building a crochet or soft-toy programme and want the consumption worksheet we use — count conversion, piece-weight measurement sheet, waste allowance schedule and the reconciliation format — send the piece weight you are working to and the yarn you have in mind, and we will return it filled in for your order.

Related reading: costing after the quotation, which covers the labour and overhead lines that sit beside the yarn; shortage and overrun tolerance, where the allowance is reconciled; and yarn dye lots, for what happens when the same count arrives in a different batch.

What does 30 tex actually mean?

Thirty grams per 1,000 metres. Tex is a direct system: a heavier yarn has a larger number. One kilogram of 30 tex yarn contains 33.3 kilometres of it, which is the figure that connects the count to piece weight and to how far a yarn order will go.

How do I convert Ne to tex?

Divide 590.5 by the cotton count. The constant comes from the definition — 840-yard hanks per pound — combined with one pound being 453.59237 grams and one yard being 0.9144 metres, which gives 496,055 yards per pound and therefore 590.5 hanks. For the worsted count the corresponding constant is 885.8, because a worsted hank is 560 yards.

Is "30/2" the same as "2/30"?

Not reliably. The trade convention is count first and ply second, so 2/30 Nm means two plies of a 30 Nm single, giving 15 Nm or 66.7 tex. But the notation is read the other way often enough that a specification should state the folded construction in words as well as the resultant linear density. Ambiguity here is a factor-of-two error, not a rounding error.

Why does the yarn weigh more than the length suggests?

Because of moisture. Yarn is sold on commercial mass — the oven-dry mass grossed up by the conventional moisture regain for the fibre, which is 8.5 per cent for cotton and 16 per cent for wool. One kilogram of cotton yarn at 8.5 per cent regain contains 921.7 grams of dry fibre. Both parties to the contract are buying on the same basis, but a cost sheet built on oven-dry mass and a purchase order built on commercial mass will not agree.

How is consumption measured for a crochet piece?

By unravelling finished, fully trimmed pieces and weighing the yarn, on a sample large enough to take a median rather than a mean — ten pieces is a workable minimum. Theoretical routes exist: area density works on flat panels and fails on openwork, and stitch count multiplied by calibrated yarn per stitch is the only method that scales to a new design, but it needs calibrating against a real piece before it can be trusted.

Should the spec state a craft weight or a count?

Both, with the count in charge. Craft weight names such as DK or worsted belong to a gauge convention, not to a linear density, and a UK four-ply and a US four-ply are different yarns. A statement of metres per 50 gram ball is already a linear density, and it is the form a spinner can buy against.

Why do two quotes for the same piece differ so much?

Usually the yarn line, and usually in one of three ways: consumption measured on a first-off rather than a production piece, a count taken from a label rather than a test, or a waste allowance that covers a different set of losses. The differences are small per piece and permanent per programme, which is why they are worth pinning down in the RFQ rather than discovering at the first reconciliation.

Related: labour minutes and standard time — how the time is measured and rated, what the allowance covers, and why the first hundred pieces are not the thousandth.

Related: quotation currency and exchange-rate clauses — which currency the price is measured in, which one arrives, and the five components of a clause that works in both directions.

Want the consumption worksheet we use? Send the piece weight you are working to and the yarn you have in mind, and we will return the count conversion, piece-weight measurement sheet and waste allowance schedule filled in for your order.

OEM/ODM process · WhatsApp